Digi-Gage Pump Controller

Digi-Gage Electronic Pump Controller

Digi-Gage Electronic Controller


Product Status: NOT ACTIVE

The Digi-Gage has been replaced by the Digi-Gage Plus

Constant Speed Controller

Product Overview

The Digi-Gage is a level monitoring system capable of controlling pumps or measuring wet wells and tank levels. This exceptional versatility has been proven in a broad spectrum of applications ranging from critical control of tank levels to monitoring effluent flow in pumping stations.

The Digi-Gage delivers the control efficiency and productivity needed to meet today’s exacting standards. The system uses an internal pressure transducer (15 psi max) or a remote mounted submersible pressure transducer to monitor water and wastewater.

Models handle a variety of liquid level control requirements

  • Digi-Gage 2300 for up to 3 pumps in a duplex or triplex configuration (constant speed).
  • Digi-Gage 2400 for up to 4 pumps in a triplex or four-plex configuration (constant speed).
  • Digi-Gage 2600 for up to 6 pumps in a five-plex or six-plex configuration (constant speed).

Product Features

  • Easy to configure for simplex, duplex or triplex applications
  • Program with only three simple steps!
  • No wires or pneumatic connections to disconnect
  • Three field selectable inputs: 4-20mA; 0-10V, 0-15 psi
  • NEMA 1 housing
  • Easy to read ½” high 7 segment LED
  • Differential level control
  • Level indication (0 – 999 max)
  • 15 discrete LED’s for Mode/Status indication
  • EEPROM (electrically erasable programmable read only memory) lasts for 100 years – no battery back-up required
  • Draw-out chassis construction
  • Pneumatic connector accepts standard 1/4” OD flex tubing
  • Pump up or pump down capability
  • Manual or automatic alternation
  • Performs self-diagnostics upon power up to maintain optimum status
  • MODBUS communications capability
  • Lag pump start delay of ten seconds
  • 100% digital technology — virtually eliminating all sources of drift or error.
  • Level simulation by using UP and DOWN arrow keys
  • Works with Scada Express for implementation of remote station monitoring and control.

Typical Wiring Diagram for DG2400-232-24AC

Digi-Gage typical wiring diagram

Typical wiring for a Digi-Gage 2400

Technical Specifications

  • Input Power: 24VAC, 8.5 VA, 350mA
  • Environment: Ambient Temperature (-10°C to 70°C)
  • Display Range: Keypad selectable, 0-999, 0-99.9, 0-9.99, 0-.999
  • Resolution: 0.006%, 14 bit A/D
  • Input Options: 4-20mA (50 ? impedance), 0-10 VDC (>150K ? impedance), 0-15 psi (clean, dry air only)
  • Memory: NOVRAM EEPROM 100 Year Memory. No batteries needed
  • Programming: Via front panel function keys
  • Display: .5” high 7 segment red LED, 3 digit
  • Housing: Type 1, NEMA 1
  • Discrete Outputs: 8 contacts, SPST, [email protected], 4 pumps, 2 alarms (high and low) 2 bubbler controls (isolate and purge)
  • Analog Output: 4-20mA (600 ? load max)
  • Linearity: +/- .005% analog output; +/- 0.1% pneumatic input
Dimensions of the Digi-Gage

Typical dimensional data


  • Physical Dimensions H x W x D: 3.78″ x 3.78″ x 7.32″
  • Depth behind panel: 6.4″ max
  • Panel cutout H x W: 3.6″ x 3.6″